Make an informed decision.

Condensation – An annoying cold weather problem

Condensation is the accumulation of liquid water on relatively cold surfaces. In this article I have attempted to inform the causes and cures of the condensation.
How does it form:
Condensation on window

Almost all air contains water vapor, the gas phase of water composed of tiny water droplets. The molecules in warm air are far apart from one another and allow the containment of a relatively large quantity of water vapor. As air cools, its molecules get closer together and squeeze the tiny vapor droplets closer together, as well. A critical temperature, known as the dew point, exists where these water droplets will be forced so close together that they merge into visible liquid in a process called condensation. This liquid starts forming on the coldest surface of the house, which is the window glass.

Lets briefly talk about a slightly different type of condensation here as well, which forms between two panes of double-pane windows. Double-pane windows have a layer of gas (usually argon or air) trapped between two panes of glass that acts as insulation to reduce heat loss through the window. Other types of gas used in this space have various effects on heat gain or loss through the window. Some windows also have a thin film installed between panes that separates the space between the panes into two spaces, further reducing heat loss and heat gain through the window. If multiple-pane windows appear misty or foggy, it means that the seal protecting the window assembly has failed.

Foggy window

The seal failure is generally caused due to saturation of silica desiccant material absorbing the infiltrating moisture inside the space between two panes.

A double-paned window that appears foggy or that has visible condensation has failed and needs to be repaired or replaced.

What causes it to form:

Condensation causes

Condensation is caused by high humidity which is in turn caused by a number of factors including but not limited to:

  1. People and pets (breathing, sweating, intense activity)
  2. Plants
  3. Shower
  4. Cooking
  5. Clothes washer/dryer
  6. Building material in new construction

What happens if it is neglected:

Condensation damage

Mold and wood-staining fungi can grow on a wetted organic (wood, paint, paper) surface above 15 deg C. and 60 % Relative Humidity. For wood destroying fungi to grow, though, wood fibers must be saturated (about 30% moisture content) and warm. Most building experts consider wood above 18 to 20 % moisture-content to be at risk of rot or mold.

These decay causing fungi grow fast at a warmer temperature, but can grow at lower temperatures, as low as 0 degC. depending on the mold genera and species. Indoor mold is both a rot or building damage hazard and a potential indoor air contaminant that can be a serious problem especially for people who are sensitive such as people who are immune-impaired, allergic, asthmatic, or have other medical or respiratory vulnerability.

Both building rot repair and building mold remediation jobs can be very costly where large areas are involved.

Symptoms of too much or too little humidity

Condensation Control

In the winter, keep the relative humidity low (in the range of 30-45% – lower as it gets colder outside). Purchase an inexpensive hygrometer to monitor humidity. Typical residential hygrometer

Here are some ways to control humidity:

  1. Keep your HRV (or ERV) running if your home has one.
  2. Run kitchen and bathroom exhaust fan every time and keep them on for 5-10 minutes after use.
  3. Make sure your clothes dryer and basement bathroom vents actually exhausts outside of the house
  4. Open the window curtains for at least few hours to allow air to circulate between the curtain and the window
  5. Indoor plants add to humidity. Do not have too many plants.
  6. Check and make sure there is no water leak from outside or plumbing

Thermal Imaging as a Detection Tool

Infra Red images

Under the right conditions, it’s possible to use an infrared (IR) camera to detect failed windows or moisture damage. IR cameras are designed to record differences in temperature. Prism Home Inspections can assist with detecting moisture leaks and resultant damage before it becomes difficult to resolve.

Ash Bhatt

http://www.prismhomeinspections.com

View more posts from this author

Leave a Reply

Your email address will not be published. Required fields are marked *